Imcold X-Wing - discussion/building thread (http://xwingpm.wz.cz/)

[starbuck]

Something I forgot. There is a small error in the description file as can be seen in the attached screenshot.

 

[zathros]

Good to point these things out, is one an end piece, or are they both the same part, just mislabeled?

 

[starbuck]

Parts no 3 and parts no 5 are different parts. Parts 3 are the end enforcements and are bigger.

 

[starbuck]

Next parts identified and ready for processing. Also here some additional details I am gonna use.
.....and cut and glued to additional layers to get the correct size.

 

[bigpetr]

Something I forgot. There is a small error in the description file as can be seen in the attached screenshot.

Thank you for pointing this out, Starbuck.

To sum it up - parts are mislabeled in the instruction drawing. They are corectly designed and labeled in the template itself.

 

[starbuck]

Thank you for pointing this out, Starbuck.

To sum it up - parts are mislabeled in the instruction drawing. They are corectly designed and labeled in the template itself.

This is exact, what I wanted to say.

 

[starbuck]

Next parts put together.
Tip:Before gluing, check that these parts fit to the wings. I first glued inside and then they did not fill the white parts on the wings.
Next parts cut out. I do not habe an exact idea how and where to place them. I hope my plastic model will show me the way.

 

[Dagger]

Very good work! I hope you find the place of those pieces, the thread of Bigpert can serve as a guide.

 

[bigpetr]

Hope this helps..

 

[zathros]

Wow!! Awesome!! )

 

[starbuck]

@bigpetr - OH YES IT DOES HELP - MANY THANKS.
Thats why I love zealot.com - you will always get help if you need.
-------
@ part 1 in bigpetr´s picture it is named w19 in the instruction, but I think it should be named w26.

 

[starbuck]

Additonal question regarding bigpetrs part 6.
Why double? Optional which to use as they have different colours?
----------------------------------------------------------------------------
I tried all possible combinations and decided to take the brighter parts, as they fit better to the rest of the wing.
I glued them on an additional layer of paper to make them pop-up.
Pictures to follow.

 

[starbuck]

Now I have all parts pre-assebled. Before glueing together I will paint the edges.
I think that I will try to assemble with moving wings. The stick and the movers are prepared.

 

[starbuck]

Ok first two wings done. I am not sure how the moving wings have to be installed. I think it might be seen better when all wings are ready.

Now I will do the other wings, witch will take some time

 

[starbuck]

some posts before:
@ Additonal question regarding bigpetrs part 6.
Why double? Optional which to use as they have different colours?
-----
The answer is: parts are needed on both sides of the wing. I forgot to place them on the inner side - you can also see on the picture.
Meantime corrected;-)

 

[bigpetr]

Thats it.
I just wanted to ssy that .

 

[zathros]

Excellent workmanship! thumbsup

 

[Gandolf50]

Nice!!

 

[starbuck]

All 4 wings finalized.

Next problem/topic is to place them in a moveable position.

And then the lasers. Hmm....checking the parts I think they are going to be difficult. Will see.

 

[starbuck]

Based on the small parts I decided to make a test to be sure to avoid mistakes. Most parts are on thin paper, only few are made of thicker paper, which was also one of the reasons for a testbuild. Never worked with thin paper before. (Beside adding an additional layer to a part.)
Here first picture.