Chuffy70
Reaction score
1,699

Latest activity Postings About

    • Chuffy70
      Chuffy70 replied to the thread let the insanity begin.
      Slowly does it... as they say. Do you think you'll paint it clean or dirty - i.e factory fresh, or battlefield weary?
    • Chuffy70
      Chuffy70 reacted to seraphim's post in the thread let the insanity begin with Like Like.
      cheers - ill be using acrylics, probably Army painter range but not sure yet. The main colour will be red, my youngest used to have an...
    • Chuffy70
      Chuffy70 reacted to zathros's post in the thread Finally. with Like Like.
      The two full Hulls that were printed right side up, then, the other, upside down. Lots of supports. The opposite sides were printed...
    • Chuffy70
      Chuffy70 reacted to Walter2's post in the thread AT-ST with Like Like.
      ...and we continue with the top and the movable access hatch...
    • Chuffy70
      Chuffy70 reacted to Walter2's post in the thread AT-ST with Like Like.
      As mentioned above, I use the punch and turn it three to four times by hand, do not tap it. This way I achieved a nice round hole. The...
    • Chuffy70
      Chuffy70 reacted to Walter2's post in the thread AT-ST with Like Like.
      The lower parts are now finished (green), now it's time to continue with the upper legs (red).
    • Chuffy70
      Chuffy70 reacted to Walter2's post in the thread AT-ST with Like Like.
      Hello folks, I feel like a surgeon and watchmaker at the same time. You can't get very far without a scalpel (!) and fine nail...
    • Chuffy70
      Chuffy70 reacted to Walter2's post in the thread AT-ST with Like Like.
      Phase two. Cut out, fold and glue. I cut out a part with four leaves glued together as a test. Important: cut out and fold exactly! This...
    • Chuffy70
      Chuffy70 reacted to Walter2's post in the thread AT-ST with Like Like.
      The beginning. I thought about the easiest and most beautiful way to punch the holes. After several attempts with scrap paper, the best...
    • Chuffy70
      Chuffy70 replied to the thread WH40K Marauder Destroyer.
      'Fan'tastic and 'exhausting' looking work ;)
    • Chuffy70
      Chuffy70 reacted to Rhaven Blaack's post in the thread WH40K Marauder Destroyer with Like Like.
      This is a very easy process. I divided the circle into 16 equal parts with pencil lines. Cut the circle into 8 equal wedges. Score the...
    • Chuffy70
      Chuffy70 reacted to Rhaven Blaack's post in the thread WH40K Marauder Destroyer with Like Like.
      Moving on to the engine intake assemblies. YOU WILL HAVE TO MAKE TWO COPIES OF PARTS SHEETS 11 & 12 TO GET ALL OF THE PARTS (77, 78,79...
    • Chuffy70
      Chuffy70 reacted to Rhaven Blaack's post in the thread WH40K Marauder Destroyer with Like Like.
      Moving on to the engines now. I started with the exhaust plates. I printed out enough parts so that I could laminate each layer to...
    • Chuffy70
      Chuffy70 reacted to seraphim's post in the thread let the insanity begin with Like Like.
      im still here, fighting my way through a mountain of card and glue lol :biggrin: believe it or not im still working on the feet, getting...
    • Chuffy70
      Chuffy70 replied to the thread let the insanity begin.
      Nice and solid looking - what paints and colours will you be using?
  • Loading…
  • Loading…
Top