Recent content by fuchsjos

  1. F

    HMS Victory, Shipyard, 1:96

    Thank's to all for the attention to my thread. @Sebret: I Don't know if there is a model af the film in the market but it looks like they have used a model of the Victory for some film cuts. Some details in the film are definitly from the Victory and on other scenes it looks like an other...
  2. F

    HMS Victory, Shipyard, 1:96

    Hello friends! Thank you for all the nice comments and for the attention to my reports ... ... and now the show goes on: After finishing of the channels next step was building the keel. But before I reduced the glossy shine with a cloud of colorless flat finish. The keel is a very...
  3. F

    HMS Victory, Shipyard, 1:96

    Thank you to all of you for the nice comments - it is still showing mem that it is right to do all the work. @timhinds1@cox.net: The most heard words from my honey are the words: 'You're complete buggy, my dear!' :-) Attention! The channel support brackets are made of 1 mm aluminium wire -...
  4. F

    HMS Victory, Shipyard, 1:96

    This three parts are the original print for one channel in the kit. Altogether they should show a thickness of 2 mm. In the middle of the part I use a 0,9 mm thick cardboard and cut some grooves, where I glue 3 anlge brackets made of 1 mm iron wire. This wires I will glue into some holes...
  5. F

    HMS Victory, Shipyard, 1:96

    @SCEtoAUX: I have arrange a big place in my dining room where it will stay in place - it is too big to go on tour with it :-) @Iriera: Thank you for your kind works, but I don't think, that I'm a master - I still try to do my best. @Elliot: Thank you too - and don't be afraid - this...
  6. F

    HMS Victory, Shipyard, 1:96

    After finishing of the gratings for the upper deck I glued them onto the deck. The printed borders were a little bit to big and I made some little frames to cover this failure. Before working on with the decks I had to make the channels, because for the mounting of them it is also...
  7. F

    HMS Victory, Shipyard, 1:96

    After having an idea about making the gratings I wanted to try it out. First I printed it out to 0,4 mm cardboard and prepare the tools. Took the sharp knife and cut some small slots. Did the same with another print but the other direction and glue both to another piece of...
  8. F

    HMS Victory, Shipyard, 1:96

    Here I show you a closer look at my workshop. It is full of junk, tools and materials and it is not neatly clean up. But I love to spend my few freetime in this chaos. The most important thing for me is enough light - so I use three fluorescent lamps with daylight color - also very good to take...
  9. F

    HMS Victory, Shipyard, 1:96

    Hi, Iriera, Nice, to meet you again and a heartful 'Thank you' - it looks like, you are lurking around in many different forums, like me. Kindly regards to Spain Josef
  10. F

    HMS Victory, Shipyard, 1:96

    Time for the second side. After the experiences with the port side it is possible to explain more details on the starboard. First step was the adjusting of the fenders, which made some troubles on the port side. This time the mounting of the fenders was a fully success. After...
  11. F

    HMS Victory, Shipyard, 1:96

    Thanks to all for their attention to my build of the Victory. @timhinds ... You're right - this build need a lot of patience ... and you're right too, that the formers look quite good - so perhaps I start a new thread to show the formers of a historical ship in a complaisant look? Servus...
  12. F

    HMS Victory, Shipyard, 1:96

    For the decorative strips I cut first a stripe off cardboard and stick it on a baseplate. With diluted white glue I form a fillet weld. Now the baseplate is cut in such a way that by the original stripe remaining only more a narrow bar. The new cutting edge was soften again with a...
  13. F

    HMS Victory, Shipyard, 1:96

    Thank's to all for your compliments - you are so kind to me. @Iriera: I have bought this tools there: Horst zu Jeddeloh | Goldschmiedebedarf ; Goldschmiedewerkzeuge ; Goldschmiedewerkzeuge ; Juwelierbedarf ; Schmuckfurnituren ; Halbfabrikate ; Schmuckketten | Webshop This is a special shop...
  14. F

    HMS Victory, Shipyard, 1:96

    Hi, Tunny ... don't mention! Have some more ... The painting for one side (port side) is ready. After making the coloring with airbrush I used dry brushing and washing to reach a smart weathered effect. The colors were used after RAL standard (Yellow - RAL 1017, Red - RAL 3011, Black - RAL...
  15. F

    HMS Victory, Shipyard, 1:96

    @Nemesis7485: Thank you! The time for the rigging will come, but I think it will be end of next year. To get the right position for the gunwales I used transparent airbrush masking film and mark the positions with a needle. Transfer of the pinholes to the cover plate and cutting with a...
Top